Just how do you really feel with regards to A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't exactly rocket science, but it does call for solid plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a reasonably challenging task. If the old tub is conveniently easily accessible, the job can move easily; if you have to open up a wall surface to eliminate the old bathtub as well as position the brand-new bathtub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old tub as well as set in the brand-new one. Ensure you have actually qualified on your own for the task and fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed job, it is better to think about employing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This write-up will aid you set up a new tub in your washroom if you have currently purchased a brand-new tub as well as do not need to alter the arrangement of your previous water system pipelines.
Your devices as well as product checklist need to consist of the following:
Getting ready for the Setup
First of all, the sustaining structure supplied with the bathroom needs to be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the versatile tap ports to the bottom of both taps using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome because of the limited access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will originate from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. As soon as the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before going on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are helpful in uniformly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by checking the level and readjusting the feet on the bath tub until the level reads degree.
To install taps, fit all-time low of the furthest adaptable tap adapter to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water system and also inspect all joints and also new pipework for leakages and also tighten them if required. Load the bathtub and additionally check the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's user's manual. Tiling and securing around the bath tub should wait up until the bath tub has been made use of at least once as this will certainly resolve it into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washers remain in area in between the faucet and the sink. Secure the tap in place with the maker given backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former type should be connected to the tap ends first, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a rigid seal, causing the water to penetrate the wall between the bath and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling below.
You can select from a range of coloured sealants to blend in your components and also installations. They are offered in tubes as well as cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealant can fracture relatively early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the market. It is advisable to fit the ceramic tiles using water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that write-up about Installing A Bathtub from an acquaintance on another site. Do you know another person who is excited by the subject? Do not hesitate to share it. Thanks for going through it.
Contact Us Now